Rastergraf Eclipse3 Series Bedienungsanleitung PDF herunterladen (Seite 39)

Rastergraf

Installing Your Peritek Graphics Board 2-7

2. Open the computer and remove the CPU board onto which the

graphics PMC board is to be installed. Identify an empty PMC location

(generally there are one or two on a given CPU board). The graphics

PMC board is a Universal PMC/PCI device and can be plugged into a

PMC port which uses either 5V or 3.3V signaling.

3. Take care to optimize airflow by blocking off unused slots in the card

cage, and arrange the boards to permit optimum airflow through them.

Caution

The static electricity that your body builds up normally can seriously

damage the components on the graphics board.

Figure 2-2 Installation of a PMC Module into an Emerson MVME2604

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 84 85

Eclipse3 Series 1
User’s Manual 1
Table of Contents 2
Figures and Tables 3
Introduction 5
Getting Help 6
Board Revisions 6
Notices 7
Introduction - 4 8
Chapter 1 9
General Information 9
1.2 Functional Description 10
Rastergraf 11
General Information 1-3 11
1-4 General Information 12
1.2.2 DVI Digital Output 13
1.2.3 Software Support 13
Host PCI Bus 14
1.3 Additional References 15
1-8 General Information 16
General Information 1-9 17
1-10 General Information 18
General Information 1-11 19
1-12 General Information 20
1-14 General Information 22
1.5.1 VGA Connector 23
1-16 General Information 24
1.5.2 DVI-I Connector 25
1-18 General Information 26
General Information 1-19 27
1-20 General Information 28
A B C D E 29
Z A B C D E F 30
1.6 Monitor Requirements 31
1-24 General Information 32
Chapter 2 33
Installing Your Peritek 33
Graphics Board 33
2.2 Unpacking Your Board 34
2.3.1 Interrupt Settings 35
2.3.2 Address Settings 35
2.3.3 Changing the Jumpers 36
PMC Slot 1 40
PMC Slot 0 40
Now, go to Section 2.7 41
2.7.2 Checking your Display 48
2.8.1 Multiboard Operation 49
2.9.1 Multiboard Operation 52
2.11 Final Checks 57
Chapter 3 59
Programming On-board 59
Devices 59
3.2.1 Introduction 61
3.2.2 Host Bus Interface 61
3.2.3 Frame Buffer 61
Block Diagram 62
3.2.5 Drawing Engine 63
3.2.7 CRT Controller 64
3.2.8 Memory Controller 64
3.2.9 VGA Core 64
(1279,0) 66
(0,1023) (1279,1023) 66
3.3 Borealis Clocks 68
3.6 Video Timing Parameters 71
Horizontal Border 73
Horizontal Blank 73
Horizontal Retrace 73
3.6.2 Pan and Scroll 74
3.8 Talk To Me Through I 77
2 79
79
3.10 Flash EEPROM 80
3.11 Serial EEPROM 80
3.12 Interrupts 80
Chapter 4 81
Troubleshooting 81
4.1 General Procedures 82
Maintenance 83
Warranty 83
Return Policy 84
Out of Warranty Service 84

Kommentare zu diesen Handbüchern

Keine Kommentare

Rastergraf Eclipse3 Series Bedienungsanleitung Seite 39

Kommentare zu diesen Handbüchern